0-60 and 1/4 miles times

61630 Views 306 Replies 52 Participants Last post by TJ_inMI, Nov 11, 2014

Triton05

Discussion Starter · Mar 23, 2013 (Edited)

For what its worth. Via an in car GPS based tracking application.

I was able to pull a 0-60mph in 6.0sec flat ( with moderate wheel spin in 1st ) and a 1/4 mile in 15.0sec @ 91mph .. ( forgot to take traction control off, can probably pull off 14.8sec on a good launch )

Both runs were done with 1/4 tank of gas 89 octane. Its also pretty chilly here. 45*F at the time of testing.

161 - 180 of 307 Posts

SnailPower

· #161 · May 24, 2014

I'm automatic.

LitosWay

· #162 · May 24, 2014

I'm m/t

LitosWay

· #163 · May 24, 2014

SnailPower said:
I'm automatic.

What Tommy run?

SnailPower

· #164 · May 24, 2014

LitosWay said:
What Tommy run?

Not my place to say, but I'm sure he'll chime in soon.

My best run was [email protected] 2.15 60'

LitosWay

· #165 · May 24, 2014

Okay.. you on stock rubber?

eviljazz

· #166 · May 24, 2014

Wtf I can't go lower 15

SnailPower

· #167 · May 24, 2014

LitosWay said:
Okay.. you on stock rubber?

Stock tires. I put them to 32 psi and launched at 2300RPM. I could probably launch at 2500, but its difficult because the brakes don't hold the car from rolling.

I figure in the winter season I should run 14.1-14.2.

LitosWay

· #168 · May 24, 2014

Yeah I launched around 2k when I tried 25 I was spinning like no tomorrow lol and evil we are tuned lol if i can get the launch right I'm pretty sure I have a 13 sec car even if it's 13.9

Darkhill240

· #169 · May 24, 2014

SnailPower said:
Stock tires. I put them to 32 psi and launched at 2300RPM. I could probably launch at 2500, but its difficult because the brakes don't hold the car from rolling.

I figure in the winter season I should run 14.1-14.2.

Automatic problems.

I typically launch at 32~3500 with no hop. 34 psi. manual has better launches

SnailPower

· #170 · May 24, 2014 (Edited)

3

Darkhill240 said:
Automatic problems.

I typically launch at 32~3500 with no hop. 34 psi. manual has better launches

I can probably get a 2.0 60' out of it with a lot of practice, not bad for stock tires. I'd say auto is better for launches than manual for sure.

Here's my timeslips and logs to go with them.

Density Altitude: 2369'

DIY SRI - https://docs.google.com/spreadsheets/d/117ZCXM9e37k82n-Dh6WMrqil4GI0S5-Zl3r8jNfaZj0/edit?usp=sharing

Text Font Line Document Monochrome

First run wheel hop bad, lowered pressure on second run and didn't wheel hop.

TS SRI (Full length) - https://docs.google.com/spreadsheets/d/1TPQZ39ej7G01GupflV1jYpeoMZ7bBKANVhsmDqvcnXY/edit?usp=sharing | https://docs.google.com/spreadsheets/d/1ABtMEmc8sZW49N8BB7XB2wAHCqCpbzNv7BAVpFi1pi0/edit?usp=sharing

Text Font Line Design Document

TS SRI (Cut about 12") - https://docs.google.com/spreadsheets/d/1CQ0aeBtAtyvHPvDo3k2-dKLaAjTgsFPQaWWh8sNsiZY/edit?usp=sharing

Last timeslip was me and Tommy. I was on the right.

See less See more

Gerid

· #171 · May 24, 2014

Snail, I wish I still lived in baton rouge... Loved No Problem raceway! I also think we'd be good friends, as I'm super cool! LMAO! Nice runs btw, I'll have to go check your thread to see what all you got done to it! Also was this done on the stock IC iirc!? If so, not bad as you were seeing consistent numbers with so many runs. Confirms my faith in the stock IC.

SnailPower

· #172 · May 24, 2014

Gerid said:
Snail, I wish I still lived in baton rouge... Loved No Problem raceway! I also think we'd be good friends, as I'm super cool! LMAO! Nice runs btw, I'll have to go check your thread to see what all you got done to it! Also was this done on the stock IC iirc!? If so, not bad as you were seeing consistent numbers with so many runs. Confirms my faith in the stock IC.

We're all super cool in Louisiana

Yep, stock intercooler. Heat soak was an issue, but not as bad as it would have been with some other FMIC... Still waiting on Tork's upgrade IC.

Reactions: 1

LitosWay

· #173 · May 24, 2014

SnailPower said:
We're all super cool in Louisiana

Yep, stock intercooler. Heat soak was an issue, but not as bad as it would have been with some other FMIC... Still waiting on Tork's upgrade IC.

What did ya do with your other fmic pm if you dint wanna post it I am curious

SnailPower

· #174 · May 24, 2014

Put it back in it's box and posted it for sale.

Reactions: 1

LitosWay

· #175 · May 24, 2014

SnailPower said:
Put it back in it's box and posted it for sale.

Do yoy think it could be that yoy just received a faulty ic?

SnailPower

· #176 · May 24, 2014

LitosWay said:
Do yoy think it could be that yoy just received a faulty ic?

Sure it's possible. I inspected the core and it looked fine though. It's kind of hard to make a faulty intercooler core.

LitosWay

· #177 · May 24, 2014

SnailPower said:
Sure it's possible. I inspected the core and it looked fine though. It's kind of hard to make a faulty intercooler core.

I mean I don't know much but sometimes things are just faulty have you spoke with the vendor?

SnailPower

· #178 · May 24, 2014

LitosWay said:
I mean I don't know much but sometimes things are just faulty have you spoke with the vendor?

This kind of conversation is best in PMs.

LitosWay

· #179 · May 24, 2014

SnailPower said:
This kind of conversation is best in PMs.

PM me bro ;p haha

[email protected]

· #180 · May 24, 2014

just saying.. we have no issues with heating up or heat soak

Reactions: 2

161 - 180 of 307 Posts

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.