Joined
·
176 Posts
What website has the best priced injen CAI?? The best I've gotten is eBay at $230
Injen Cold Air Intake
1 - 20 of 26 Posts
Joined
·
403 Posts
Try ebay.
Or Very similar
AEM® 21-724C - Hyundai Veloster 2013 Cold Air Intake System
Dyno info http://www.aemintakes.com/dynocharts/AEM-21-724-AITS.pdf
or if you want to save a few more $$$
http://www.velosterturbo.org/forum/turbosocks-performance/2486-new-3-cai-system-3-fmic-cai-ram-air-system.html
Or Very similar
AEM® 21-724C - Hyundai Veloster 2013 Cold Air Intake System
Dyno info http://www.aemintakes.com/dynocharts/AEM-21-724-AITS.pdf
or if you want to save a few more $$$
http://www.velosterturbo.org/forum/turbosocks-performance/2486-new-3-cai-system-3-fmic-cai-ram-air-system.html
Joined
·
176 Posts
Joined
·
71 Posts
AutoAnything | Auto Accessories & Aftermarket Parts | Truck Accessories & Car Accessories - Floor Mats, Tonneau Covers & Car Covers usually a % off coupon advertised on the site. I got the SRI injen 180 shipped.
Joined
·
1,345 Posts
Since you're from California, AutoAnything will hit you with state tax. I didn't realize it until after I had received my intake that the invoice showed tax. Stupid thing about it was that when purchasing on their website, it didn't show anything regarding tax. I ended up paying almost $200 shipped.
If you're out of state it's a good deal. If you're in CA, it may not be so great.
Forgot to include, that I purchased the short ram instead of the cold air.
If you're out of state it's a good deal. If you're in CA, it may not be so great.
Forgot to include, that I purchased the short ram instead of the cold air.
Joined
·
939 Posts
Can u share the codes, u were able to stack?I got mine from auto anytn, 15% discount, new cust discount, free shippn, and free hydro filter for like 135.
Joined
·
11,457 Posts
The cheap one is the SRI. The more expensive is the CAI.
Joined
·
418 Posts
Also, I think the IS is carb and the SP is not. At least this is what is stated on the Injen I received today
Joined
·
176 Posts
Joined
·
1,430 Posts
Here is some info about the difference between IS and SP: Injen - Performance Air Intake Systems, Exhaust Systems, Turbo Components, and Air Filters for Cars, Trucks, Motorcycles, ATV's, Boats and more!
"IS Intake Systems
The IS Series is a traditional, underhood intake system that is placed in the stock location of the factory air-box system. Each system is built from 6061, T-6 aluminum alloy to ensure the lightest design possible. Every IS system is certified by the California Air Resource Board or submitted with pending approval and backed by Injen Technology's limited lifetime warranty."
"SP Series Intake Systems
This unique design was specifically engineered with MR Technology (MegaRam), to provide maximum horsepower gains and take into consideration the air to fuel ratio's set by the Original Equipment Manufacturer. MR Technology is a sophisticated tuning process developed by Injen Technology; altering Cold Air Intake systems to be carefully tuned within Factory Safe limits. Through a series of engineered and tested air-restricted sections, the pressurized mass air is controlled to a calculated aggression, allowing for a proper air/fuel calibration. The end results allows for more reliable and consistent horsepower/torque gains. MR Technology is the World's First Tuned Intake System! Every SP system is certified by the California Air Resource Board or submitted with pending approval and backed by Injen Technology's limited lifetime warranty. (Vehicles without Mass air sensors will have special tube designs but may not include MR Technology)"
"IS Intake Systems
The IS Series is a traditional, underhood intake system that is placed in the stock location of the factory air-box system. Each system is built from 6061, T-6 aluminum alloy to ensure the lightest design possible. Every IS system is certified by the California Air Resource Board or submitted with pending approval and backed by Injen Technology's limited lifetime warranty."
"SP Series Intake Systems
This unique design was specifically engineered with MR Technology (MegaRam), to provide maximum horsepower gains and take into consideration the air to fuel ratio's set by the Original Equipment Manufacturer. MR Technology is a sophisticated tuning process developed by Injen Technology; altering Cold Air Intake systems to be carefully tuned within Factory Safe limits. Through a series of engineered and tested air-restricted sections, the pressurized mass air is controlled to a calculated aggression, allowing for a proper air/fuel calibration. The end results allows for more reliable and consistent horsepower/torque gains. MR Technology is the World's First Tuned Intake System! Every SP system is certified by the California Air Resource Board or submitted with pending approval and backed by Injen Technology's limited lifetime warranty. (Vehicles without Mass air sensors will have special tube designs but may not include MR Technology)"
Joined
·
176 Posts
thanks Hyperion, really helpful. I guess I'm shooting for the SP series then
Joined
·
3,541 Posts
love that long winded explanation that serves NO purpose on the majority of MAP based vehicles, including our car
IS = at factory location = SRI
SP = CAI extension added = CAI
IS = at factory location = SRI
SP = CAI extension added = CAI
Joined
·
3,541 Posts
wonder if I come up with some witchcraft technology and dub it TS windtunnel extrusion technology if people will take me more seriously
I am sure they do their due diligence when they come out with a new intake system but I am doubtful that they put as much as it sounds, specially when they are dealing with a turbo car on MAP. On older MAF based cars that weren't tuned as conservatively and/or didn't have 'smart' ECU's it would be a lot more critical to design an intake to keep safe AFRs
I am sure they do their due diligence when they come out with a new intake system but I am doubtful that they put as much as it sounds, specially when they are dealing with a turbo car on MAP. On older MAF based cars that weren't tuned as conservatively and/or didn't have 'smart' ECU's it would be a lot more critical to design an intake to keep safe AFRs
Joined
·
353 Posts
Add "Quantum" in there...things sound more impressive with Quantum
Turbosocks Performance Quantum FMIC Type RZ with Windtunnel Extrusion Technology*
*Comes with sticker
Turbosocks Performance Quantum FMIC Type RZ with Windtunnel Extrusion Technology*
*Comes with sticker
Joined
·
418 Posts
Short and simple.love that long winded explanation that serves NO purpose on the majority of MAP based vehicles, including our car
IS = at factory location = SRI
SP = CAI extension added = CAI
On a side note, I installed my Injen SRI today and removed it in a matter of hours. Like some have posted, the sound is just not the same as a NA car. The sound is quite obnoxious axctually and when I am going down a residential neighborhood I really have to baby the throttle. If not, it starts screaming at 1500RPM.
Don't get me wrong guys, the sound is mean and killer but not my cup of tea.
It is going up for sale as of now
1 - 20 of 26 Posts
