Veloster Turbo Forum banner
1 - 20 of 257 Posts

· Vendor
Joined
·
742 Posts
Discussion Starter · #1 ·




Looking to add a little style to your Gencoupe's or Veloster's engine bay? Replace your boring old oil cap with some brand new TurboXS hotness! The TurboXS oil cap fits like OEM but is made from highly polished black anodized aluminum. The TurboXS logo laser etched into the surface completes the look. I have LIMITED SUPPLY everyone, so message me to get YOURS TODAY

TurboXS Oil Cap Black - TurboXS
 

· Vendor
Joined
·
3,541 Posts
looks pretty nice but damn pricey considering you can get a billet oil cap off ebay for ~20$-25$ SHIPPED.
 
  • Like
Reactions: MyDianaZ06

· Vendor
Joined
·
3,541 Posts

· Registered
Joined
·
2,845 Posts
And for 60 bucks this is better than the stock cap how again?
 

· Registered
Joined
·
2,101 Posts
It shaves off .356 milligrams off stock cap weight.

behold scientific proof below!
(.356 mg x 88mph)/flux capacitor lag of 0.75 millisecond = 3whp (as mentioned above) this result does not factor in decal hp, use that at your own risk and peril.
 

· Registered
Joined
·
177 Posts

· Registered
Joined
·
718 Posts
$60 to change my oil cap to have one with a brand name on it that has literally zero performance parts for our car? WTF.

Man I'm glad I'm too broke right now to be modding my car because the aftermarket support is in all the wrong areas aside from our handful of members that are DOING WORK. Pierce, TurboSocks, ElecBlue, etc.
 
  • Like
Reactions: MyDianaZ06

· Vendor
Joined
·
742 Posts
Discussion Starter · #16 · (Edited)
$60 to change my oil cap to have one with a brand name on it that has literally zero performance parts for our car? WTF.

Man I'm glad I'm too broke right now to be modding my car because the aftermarket support is in all the wrong areas aside from our handful of members that are DOING WORK. Pierce, TurboSocks, ElecBlue, etc.
lolz.. ive posted up saying that the intake and exhaust will be out this fall. Also there is no engine management that we are aware of so it makes it hard to put out parts. We do know that SFR is working on something but yea, we are also working it
 

· Registered
Joined
·
2,523 Posts
It shaves off .356 milligrams off stock cap weight.

behold scientific proof below!
(.356 mg x 88mph)/flux capacitor lag of 0.75 millisecond = 3whp (as mentioned above) this result does not factor in decal hp, use that at your own risk and peril.

2 funny, thnx, now i get it. :)
 

· Registered
Joined
·
177 Posts
lolz.. ive posted up saying that the intake and exhaust will be out this fall. Also there is no engine management that we are aware of so it makes it hard to put out parts. We do know that SFR is working on something but yea, we are also working it
I'm not blaming you or anything like that, but a few months back you said "2-3 months" which would be basically April/May. So now we're looking at the fall?

I think I'm going to go ahead and order the Injen intake. Glad I didn't wait for the exhaust. Very happy with my Solo.
 

· Registered
Joined
·
2,101 Posts
I'm not blaming you or anything like that, but a few months back you said "2-3 months" which would be basically April/May. So now we're looking at the fall?

I think I'm going to go ahead and order the Injen intake. Glad I didn't wait for the exhaust. Very happy with my Solo.
yea, i noticed that myself when I shopping for an intake.

I saw the turbo xs post on veloster dot com (i don't know if we're allowed to link on here... forum politics have me paranoid) but the post was dated oct 2012 and they had a pic of an intake with dyno sheets and all. Then radio silence until dec 12 with an exhaust pic and vid then nothing past march, now they've switched it up from exhaust and intakes to flux capacitors and twist on caps... shame because that setup looks quite nice.
 
1 - 20 of 257 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top