[DrJepsenDC]

FEW have asked & MANY have wondered.....
.....................Is the cheap "ebay/amazon" Cat back exhaust system worth a shot?
What does it sound like? How is the installation process/fitment? Any noticeable boost in Performance?....

Good news y'all, I'm gonna give her a chance to be heard. ETA on Exhaust system is a day or two, and I will kickstart this post with an Unboxing & Initial Impressions Video.

I included the link below.

Performance Stainless Steel SS SS409 2.5" Cat Back CatBack Exhaust Muffler Kit System Polished Tips Compatible With 13-18 Hyundai Veloster 1.6L Turbo

 

[trdtoy]

I had a customer with this exhaust and it did fine and sounded good. Did 250+ whp with the car and not FBO.

 

[DrJepsenDC]

I had a customer with this exhaust and it did fine and sounded good. Did 250+ whp with the car and not FBO.

Not bad for lack of FBO!

 

[trdtoy]

Yes but all cars I tune do well

 

[DrJepsenDC]

Yes but all cars I tune do well

That right there is why I love you! The confidence with products to back it up! well.... now that that's been said.... what kind of tunes you offering? PM me if you'd prefer

 

[trdtoy]

I have very little to offer with a stock turbo VT not even FBO in the 12's ;-)

 

[DrJepsenDC]

I have very little to offer with a stock turbo VT not even FBO in the 12's ;-)

I’ll keep dreaming!! Haha.
But I’ll be having fun testing these cheap a$$ parts 😂

 

[one2manyhobbies]

I can't wait to hear this!

 

[DrJepsenDC]

Update!!! I have received the exhaust, only a few days late lol. I am going to unbox here soon and Potentially slap it on the car tonight! If not today(running out of daylight) the. For sure tomorrow. I’ll post the video links on this page 💪🏼💪🏼

 

[Drgyn]

im guessing this dint go as smooth since no update yet hope it works out was looking at same setup possible to save some cash.

 

[DrJepsenDC]

I apologize every one! I got pretty sick and wasn’t able to get Er done. After an initial inspection of removing/installing systems…. Lol go figure the part that is keeping this from moving forward is?!?…… the absurdly rusted/shit covered bolts connecting the stock pipes a over the rear axle…. Anyone have any suggestions? It literally torqued/twisted a ratchet extender from the amount of force I have applied in attempt to remove those 2 silly bolts….

 

[trdtoy]

Good 1/2" equipment, plenty of good penetrating oil, elbow grease, mother of all ugga duggas!

 

[RPW00Mirage]

and a torch, lol

 

[SkyShadex]

UGGA DUGGA. get a long pipe to put over the wrench, will make it alot easier to break it loose.

 

[Acealkaline]

https://www.autozone.com/greases-and-gear-oil/lubricant-grease/crc-freeze-off-super-penetrant/898352_0_0

Use this and that Ugga dugga technique and you should be good

 

[misnblu]

Thank you for the link. This will help with all the work I do with rusty components. 👍

https://www.autozone.com/greases-and-gear-oil/lubricant-grease/crc-freeze-off-super-penetrant/898352_0_0

Use this and that Ugga dugga technique and you should be good

 

[RPW00Mirage]

i wonder if i should get that freeze crap too... use it along side a torch? lol

 

[misnblu]

i wonder if i should get that freeze crap too... use it along side a torch? lol

I've got a broken exhaust stud on my bike that needs a good heat cold blast to hopefully get it out. 🤞
I even bought a map gas torch to help. 😁👍

 

[RPW00Mirage]

ugh for stuff like that i weld a nut to the end...

 

[misnblu]

ugh for stuff like that i weld a nut to the end...

Sounds good so when you coming over with your welder? 😂😜😉